Stainless Steel 303 (UNS S30300) Properties, Supplier Data

Stainless steels type 1.4305 is popularly known as grade 303 stainless steel. Grade 303 stainless steel is the most readily machineable of all the austenitic grades of stainless steel.

The machineable nature of Grade 303 stainless steel is due to the presence of Sulphur in thesteels composition. Whilst the Sulphur improves machining, it also causes a decrease in the corrosion resistance and a slight lowering of the toughness. The corrosion resistance of grade 303 stainless steel is lower than that for 304. The toughness is still excellent as with other austenitic grades.

Property data given in this document is typical for 303 stainless steel flange product covered by ASTM A582. ASTM, EN or other standards may cover products sold by Yaang.com. It is reasonable to expect specifications in these standards to be similar but not necessarily identical to those given in this article.

Chemical Composition of Stainless Steels

Table 1. Typical chemical composition for stainless steels 303 (UNS S30300)

%	303
C	0-0.10
Mn	0-2.0
Si	0-1.0
P	0-0.4
S	0-0.15
Cr	17-19
Ni	8-10
Fe	balance

 

Properties Composition of Stainless Steel 303 (UNS S30300)

Mechanical Properties of Stainless Steel 303 (UNS S30300)

Table 2. Typical mechanical properties for stainless steels alloy 303

Grade	303
Tensile Strength (MPa)	500-700
Proof Stress (MPa)	190 Min
Elongation A5 (%)	35

Physical Properties of Stainless Steel 303 (UNS S30300)

Table 3. Typical physical properties for stainless steels alloy 303

Property	Value
Density	8.03 kg/m3
Melting Point	1455°C
Modulus of Elasticity	193 GPa
Electrical Resistivity	0.072x10-6 Ω.m
Thermal Conductivity	16.3 W/m.K
Thermal Expansion	17.3x10-6 /K

Alloy Designations

Stainless steel grade 303 also corresponds to the following standard designations and specifications:

Euronorm	UNS	BS	En	Grade
1.4305	S30300	303S31	58M	303

Corrosion Resistance of Stainless Steel 303 (UNS S30300)

Sulphur additions to the composition act as initiation sites for pitting corrosion. This decreases the corrosion resistance of grade 303 stainless steel to less than that for 304. However corrosion resistance remains good in mild environments.

In chloride containing environments over 60°C, grade 303 stainless steel is subject to pitting and crevice corrosion. Grade 303 stainless is not suitable for use in marine environments.

Heat Resistance of Stainless Steel 303 (UNS S30300)

Grade 303 stainless steel has good resistance to oxidation when intermittently exposed to temperature up to 760°C temperatures. It also has good oxidation resistance in continuous service to 870°C. This, however, is not recommended as 303 is sensitive to carbide precipitation with continuous use at 425-860°C.

Fabrication of Stainless Steel 303 (UNS S30300)

Fabrication of all stainless steels should be done only with tools dedicated to stainless steelmaterials. Tooling and work surfaces must be thoroughly cleaned before use. These precautions are necessary to avoid cross contamination of stainless steel by easily corroded metals that may discolour the surface of the fabricated product.

Cold Working of Stainless Steel 303 (UNS S30300)

Type 303 is not readily cold workable. Some cold working is possible but sharp bending should not be attempted.

Hot Working of Stainless Steel 303 (UNS S30300)

Fabrication methods, like forging, that involve hot working like should occur after uniform heating to 1149-1260°C. The fabricated components should then be rapidly cooled to ensure maximum corrosion resistance.

Heat Treatment of Stainless Steel 303 (UNS S30300)

Grade 303 stainless steel cannot be hardened by heat treatment.

Solution treatment or annealing can be done by rapid cooling after heating to 1010-1120°C.

Machinability

Grade 303 stainless steel has excellent machinability. Machining can be enhanced by adhering to the following rules:

• Cutting edges must be kept sharp. Dull edges cause excess work hardening.
• Cuts should be light but deep enough to prevent work hardening by riding on the surface of the material.
• Chip breakers should be employed to assist in ensuring swarf remains clear of the work
• Low thermal conductivity of austenitic alloys results in heat concentrating at the cutting edges. This means coolants and lubricants are necessary and must be used in large quantities.

Welding of Stainless Steel 303 (UNS S30300)

The sulphur addition present in Grade 303 stainless steel results in poor weldability. If Grade 303 stainless steel must be welded the recommended filler rods or electrodes are grades 308L and 309 stainless steels. For maximum corrosion resistance, the welds must be annealed.

Applications of Stainless Steel 303 (UNS S30300)

Grade 303 stainless steel is used in applications that require parts to be heavily machined. These applications include:

• Nuts and bolts
• Screws
• 303 stainless steel pipe
• Aircraft fittings
• Bushings
• Shafts

Supplied Forms

Grade 303 stainless steel is typically supplied by yaang.com in the following forms:

• Round bar
• Hexagonal bar
• 303 Stainless Steel Bar
  

Source: yaang.com

For more information on this source please visit: https://www.yaang.com

Next: 303 STAINLESS STEEL UNS 30300
Prev: List of Chemical Elements