Ξ
- SITEMAP
- CONTACT US
- 8618267732328
News
Credibility ,the lifeblood of enterprise!
PRODUCT SERIES
- Fittings
- Butt Welding Fittings
- Forged Fittings
- 180 Degree Elbows
- 90 Degree Elbows
- 60 Degree Elbows
- 45 Degree Elbows
- 30 Degree Elbows
- Equal Tee
- Reducing Tee
- Concentric Reducer
- Eccentric Reducer
- Lap Joint Stub End
- Outlets
- Cap
- Bend
- Cross
- Coupling
- Stainless Steel Lateral Tee
- Bellows Expansion Joints
- Flexible Metal Hose
- Non-Standard/Custom Fittings
- Bleed & Flushing Rings
- Types of Flanges
- Anchor Flanges
- Blind Flanges
- Expander Flanges
- High Hub Flanges
- Lap Joint Flanges
- Long Weld Neck Flanges
- Nipoflanges
- Orifice Flanges
- Plate Flanges
- Ring Type Joint Flanges
- Reducing Flanges
- Slip On Flanges
- Socket Weld Flanges
- Spectacle Blind Flanges
- Square Flanges
- Spades & Ring Spacers
- Threaded Flanges
- Welding Neck Flanges
Your Location: Home > News
News - Yaang
Internal thread processing method of stamping elbow
DataTime:[2016-12-11]
Design and manufacture of a tap
The internal thread on the stamping elbow usually adopts tap for tapping processing. Because stainless viscosity is higher, chip breaking performance is poor, so prone to chip in the process of tapping scratch artifacts thread or tap the phenomenon such as collapse edge, affect the efficiency and the quality of thread. In order to prolong the service life of tap, improve the quality of thread machining, the following points should be paid attention to.
(1) to choose better tap material. Add special alloy elements, in ordinary high speed tool steel tap could obviously improve the abrasion resistance and toughness.
(2) in tap thread surface coated with titanium nitride coating, can significantly improve the tap wear resistance, heat resistance and lubricity.
(3) more appropriate tap backoff. But should pay attention to, such as large amount of backoff, prone to chip in the blade into the tap in the phenomenon of poor and tapping the thread finish.
(4) choose reasonable tool heat treatment method, in order to give attention to both tap of hardness and toughness.
(5) more appropriate Angle before the tap. But should pay attention to, such as tap rake Angle is too large, when the blade cause tap collapse edge and tapping the thread edges.
Second, the selection of tapping oil
Tapping processing for the stainless steel stamping elbow, the selection of tapping oil is very important. Tapping oil must have good cooling and lubrication and rust prevention function. Such as tapping oil cooling effect is not good, then tap easy sticky, namely before the tap threads and Angle of surface bonding stainless steel scraps. Such as tapping oil lubrication effect is bad, is poor, tapping the thread finish and tap tapping resistance is big. Stainless steel special tapping oil effect is good, can use directly. In addition, also can use tapping oil essence oil and configure, but matching to the right.
Source: Yaang Pipe Industry Co., Limited (www.yaang.com)
The internal thread on the stamping elbow usually adopts tap for tapping processing. Because stainless viscosity is higher, chip breaking performance is poor, so prone to chip in the process of tapping scratch artifacts thread or tap the phenomenon such as collapse edge, affect the efficiency and the quality of thread. In order to prolong the service life of tap, improve the quality of thread machining, the following points should be paid attention to.
(1) to choose better tap material. Add special alloy elements, in ordinary high speed tool steel tap could obviously improve the abrasion resistance and toughness.
(2) in tap thread surface coated with titanium nitride coating, can significantly improve the tap wear resistance, heat resistance and lubricity.
(3) more appropriate tap backoff. But should pay attention to, such as large amount of backoff, prone to chip in the blade into the tap in the phenomenon of poor and tapping the thread finish.
(4) choose reasonable tool heat treatment method, in order to give attention to both tap of hardness and toughness.
(5) more appropriate Angle before the tap. But should pay attention to, such as tap rake Angle is too large, when the blade cause tap collapse edge and tapping the thread edges.
Second, the selection of tapping oil
Tapping processing for the stainless steel stamping elbow, the selection of tapping oil is very important. Tapping oil must have good cooling and lubrication and rust prevention function. Such as tapping oil cooling effect is not good, then tap easy sticky, namely before the tap threads and Angle of surface bonding stainless steel scraps. Such as tapping oil lubrication effect is bad, is poor, tapping the thread finish and tap tapping resistance is big. Stainless steel special tapping oil effect is good, can use directly. In addition, also can use tapping oil essence oil and configure, but matching to the right.
Source: Yaang Pipe Industry Co., Limited (www.yaang.com)
Tel No：+86-18267732328 / Email:[email protected]
Address：Longwan District, Wenzhou, Zhejiang Province, China.
Copyright Notice © www.yaang.com Yaang Pipe Industry Co., Limited All rights reserved.
Yaang Pipe Industry Co., Ltd. is an international supplier of piping solutions for flange, butt welding fittings, socket welding fittings and threaded fittings. Our products are widely used in different industrial fields, including oil and gas, chemical industry, petrochemical industry, power plant, pulp and paper industry, environmental and water conservancy engineering, engineering projects, etc.
