Ξ
- SITEMAP
- CONTACT US
- 8618267732328
News
Credibility ,the lifeblood of enterprise!
PRODUCT SERIES
- Fittings
- Butt Welding Fittings
- Forged Fittings
- 180 Degree Elbows
- 90 Degree Elbows
- 60 Degree Elbows
- 45 Degree Elbows
- 30 Degree Elbows
- Equal Tee
- Reducing Tee
- Concentric Reducer
- Eccentric Reducer
- Lap Joint Stub End
- Outlets
- Cap
- Bend
- Cross
- Coupling
- Stainless Steel Lateral Tee
- Bellows Expansion Joints
- Flexible Metal Hose
- Non-Standard/Custom Fittings
- Bleed & Flushing Rings
- Types of Flanges
- Anchor Flanges
- Blind Flanges
- Expander Flanges
- High Hub Flanges
- Lap Joint Flanges
- Long Weld Neck Flanges
- Nipoflanges
- Orifice Flanges
- Plate Flanges
- Ring Type Joint Flanges
- Reducing Flanges
- Slip On Flanges
- Socket Weld Flanges
- Spectacle Blind Flanges
- Square Flanges
- Spades & Ring Spacers
- Threaded Flanges
- Welding Neck Flanges
Your Location: Home > News
News - Yaang
Unions and coupling
DataTime:[2016-7-13]
1, "What is the basic difference between coupling and unions?"
Both of these fittings are normally only found or used in 2" (DN50) and smaller screwed or socket-weld piping. The basic difference between a coupling and a union is that a coupling is for joining pipe to pipe or pipe to a swedge. A union is made for joining and disassemble of a part of a piping system (a steam trap or control valve, etc) for maintenance or replacement.
2, "What are the advantages of ones over others?"
The union is a higher cost item than the coupling. When you are just joining pipe you would want to use the lowest cost item. When you need the ability to disassemble the piping for removal of an item then you must use the higher cost union.
3, "Where we use coupling and where we use unions ?"
Use couplings to join pipe in pipe racks. Use unions at steam trap or control valve manifolds for removal of items for repair.
4, "Is there any guidelines or code that specifies where should we use what?"
The use of couplings or unions is not a code issue.
Both of these fittings are normally only found or used in 2" (DN50) and smaller screwed or socket-weld piping. The basic difference between a coupling and a union is that a coupling is for joining pipe to pipe or pipe to a swedge. A union is made for joining and disassemble of a part of a piping system (a steam trap or control valve, etc) for maintenance or replacement.
2, "What are the advantages of ones over others?"
The union is a higher cost item than the coupling. When you are just joining pipe you would want to use the lowest cost item. When you need the ability to disassemble the piping for removal of an item then you must use the higher cost union.
3, "Where we use coupling and where we use unions ?"
Use couplings to join pipe in pipe racks. Use unions at steam trap or control valve manifolds for removal of items for repair.
4, "Is there any guidelines or code that specifies where should we use what?"
The use of couplings or unions is not a code issue.
Tel No：+86-18267732328 / Email:[email protected]
Address：Longwan District, Wenzhou, Zhejiang Province, China.
Copyright Notice © www.yaang.com Yaang Pipe Industry Co., Limited All rights reserved.
Yaang Pipe Industry Co., Ltd. is an international supplier of piping solutions for flange, butt welding fittings, socket welding fittings and threaded fittings. Our products are widely used in different industrial fields, including oil and gas, chemical industry, petrochemical industry, power plant, pulp and paper industry, environmental and water conservancy engineering, engineering projects, etc.
